STATE INFORMATION
Cover
Preface
No. 109
No. 109-A
No. 111 - Standard Requirements for Attachment of Perimeter Woodblocking and Metal Flashing
No. 113 - Standard Requirements for Job Site Mixing of Roof Tile Mortar
No. 115 - Standard Procedures for Asphaltic Shingle Installation
No. 117 - Standard Requirements for Bonding or Mechanical Attachment of Insulation Panels and Mechanical Attachment of Anchor and/or Base Sheets to Substrates
No. 118 - Installation of Mechanically Fastened Roof Tile Systems
No. 119 - Installation of Mechanically Fastened Roof Tile Systems
No. 120 - Mortar and Adhesive Set Tile Application
No. 127 - Procedure for Determining the Moment of Resistance and Minimum Characteristic Resistance Load to Install a Tile System on a Building of a Specified Roof Slope and Height
No. 128 - Standard Procedure for Determining Applicable Wind Design Pressures for Low Slope Roof
No. 130 - Installation Criteria for Wood Shingles and Shakes Application
No. 133 - Standard Procedure for Installation of Metal Roof Systems
No. 137 - Standard Requirements for Mechanical Attachment of Single-Ply Roof Coverings to Various Substrates
No. 150 - Prescriptive Bur Requirements
No. 100-95 - Test Procedure for Wind and Wind Driven Rain Resistance of Discontinuous Roof Systems
No. 100(a)-95 - Test Procedure for Wind and Wind Driven Rain Resistance and/or Increased Windspeed Resistance of Soffit Ventilation Strip and Continuous or Intermittent Ventilation System Installed At the Ridge Area
No. 101-95 - Test Procedure for Static Uplift Resistance of Mortar or Adhesive Set Tile Systems
No. 102-95 - Test Procedure for Static Uplift Resistance of Mechanically Attached‚ Rigid Roof Systems
No. 102(a)-95 - Test Procedure for Static Uplift Resistance of Mechanically Attached‚ Clipped‚ Rigid‚ Roof Systems
No. 103-95 - Test Procedure for Self-Adhered Underlayments for Use In Discontinuous Roof Systems
No. 104-95 - Test Procedure for Nail-on Underlayment for Use In Discontinuous Roof Systems
No. 105-98 - Test Procedure for Field Withdrawal Resistance Testing
No. 106 - Standard Procedure for Field Verification of the Bonding of Mortar or Adhesive Set Tile Systems and Mechanically Attached‚ Rigid‚ Discontinuous Roof Systems
No. 107-95 - Test Procedure for Wind Resistance Testing of Non-Rigid‚ Discontinuous Roof System Assemblies
No. 108-95 - Test Procedure for Wind Tunnel Testing of Air Permeable‚ Rigid‚ Discontinuous Roof Systems
No. 110-2000 - Testing Requirements for Physical Properties of Roof Membranes‚ Insulation‚ Coatings‚ and Other Roofing Components
No. 111(A)-95 - Test Procedure for Roof Edge Termination Performance
No. 111(B)-95 - Test Procedure for Edge Metal Pull-Off Performance
No. 111(C)-95 - Test Procedure for Coping Cap Pull-Off Performance
No. 112-95 - Standard Requirements for Concrete Roof Tiles
No. 112-95 Appendix A - Clarification of Testing Frequency and Sampling Method
No. 114-95 - Test Procedures for Roof System Assemblies In the High-Velocity Hurricane Zone Jurisdiction
114-95 Appendix A - Test Procedure for Above Deck Combustibility ASTM E 108
114-95 Appendix B - Test Procedure for Simulated Dynamic Uplift Pressure Resistance of Mechanically Attached Roof System Assemblies
114-95 Appendix C - Test Procedure for Simulated Uplift Pressure Resistance of Roof System Assemblies
114-95 Appendix D - Test Procedure for Simulated Uplift Pressure Resistance of Adhered Roof System Assemblies
114-95 Appendix E - Test Procedure for Corrosion Resistance of Fasteners‚ Batten Bars and Stress Distribution Plates
114-95 Appendix F - Test Procedure for Susceptibility to Hail Damage for Roof System Assemblies
114-95 Appendix G - Test Procedure for Susceptibility to Leakage for Roof System Assemblies
114-95 Appendix H - Test Procedures for Small Scale QC and Physical Properties of Approved Roof System Assemblies
114-95 Appendix I - Test Procedure for Static and Dynamic Puncture Resistance of Roof System Assemblies
114-95 Appendix J - Test Procedure for 12 Foot by 24 Foot Simulated Uplift Pressure Resistance of Roof System Assemblies
114-95 Appendix K - Test Procedures for F.I.T. Classification of Modified Bitumen Roof System Assemblies
116-95 - Test Procedure for Air Permeability Testing of Rigid‚ Discontinuous Roof Systems
117(A)-95 - Test Procedure for Withdrawal Resistance Testing of Mechanical Fasteners Used In Roof System Assemblies
117(B)-95 - Test Procedure for Dynamic Pull-Through Performance of Roofing Membranes Over Fastener Heads or Fasteners with Metal Bearing Plates
117(C)-95 - Test Procedure for Dynamic Pull-Off Performance of Roofing Fastener Heads or Fasteners with Bearing Plates
121-95 - Standard Requirements for Testing and Approval of Roofing Adhesives‚ Mastics and Coatings
123-95 - Standard Requirements for Mortar Used In Mortar Set Tile Systems
123-95 Appendix A - Standard Requirements of Tile Adhesive Used to Repair or Supplement Tile Attachment
124-95 - Test Procedure for Field Uplift Resistance of Existing Membrane Roof Systems and In Situ Testing for Reroof and New Construction Applications
125-03 - Standard Requirements for Metal Roofing Systems
126-95 - Standard Procedures for Roof Moisture Surveys
131-95 - Standard Requirements for Thermoplastic Olefin Elastomer Based Sheet Used In Single-Ply Roof Membrane
131-95 Appendix A - Test Procedure for Thickness Measurement of Coating Over Class SR Olefin Elastomer Based Sheet Roofing
132-95 - Standard Requirements for Testing and Approval of Sealants Used In Roofing
135-95 - Standard Requirements for Fiberglass Reinforced Tile‚ Shingles or Panels and Fiber Cement Shingles‚ Shakes or Panels
138-95 - Standard Requirements for Aluminum Pigmented Emulsified Asphalt Used as a Protective Coating for Roofing
139-95 - Standard Requirements for White Roof Patch Specification
140-95 - Standard Requirements for Nonfibered Roof and Foundation Coatings
141-95 - Standard Requirements for Coal Tar (Cutback) Roof Coating‚ Brushing Consistency
142-95 - Standard Requirements for Coal Tar Roof Cement‚ Asbestos Free
143-95 - Standard Requirements for White Elastomeric Roof Coatings Used for Coating Built Up Roofs and Metal Roofing Systems
201-94 - Impact Test Procedures
202-94 - Criteria for Testing Impact & Nonimpact Resistant Building Envelope Components Using Uniform Static Air Pressure
203-94 - Criteria for Testing Products Subject to Cyclic Wind Pressure Loading
301-94 - Testing Laboratory
Top
Previous Section
Next Section
To view the next subsection please select the Next Section option.
Top
Previous Section
Next Section
To view the next subsection please select the Next Section option.
