STATE INFORMATION
Cover
Preface
No. 109
No. 109-A
No. 111 - Standard Requirements for Attachment of Perimeter Woodblocking and Metal Flashing
No. 113 - Standard Requirements for Job Site Mixing of Roof Tile Mortar
No. 115 - Standard Procedures for Asphaltic Shingle Installation
No. 117 - Standard Requirements for Bonding or Mechanical Attachment of Insulation Panels and Mechanical Attachment of Anchor and/or Base Sheets to Substrates
No. 118 - Installation of Mechanically Fastened Roof Tile Systems
No. 119 - Installation of Mechanically Fastened Roof Tile Systems
No. 120 - Mortar and Adhesive Set Tile Application
No. 127 - Procedure for Determining the Moment of Resistance and Minimum Characteristic Resistance Load to Install a Tile System on a Building of a Specified Roof Slope and Height
No. 128 - Standard Procedure for Determining Applicable Wind Design Pressures for Low Slope Roof
No. 130 - Installation Criteria for Wood Shingles and Shakes Application
No. 133 - Standard Procedure for Installation of Metal Roof Systems
No. 137 - Standard Requirements for Mechanical Attachment of Single-Ply Roof Coverings to Various Substrates
No. 150 - Prescriptive Bur Requirements
No. 100-95 - Test Procedure for Wind and Wind Driven Rain Resistance of Discontinuous Roof Systems
No. 100(a)-95 - Test Procedure for Wind and Wind Driven Rain Resistance and/or Increased Windspeed Resistance of Soffit Ventilation Strip and Continuous or Intermittent Ventilation System Installed At the Ridge Area
No. 101-95 - Test Procedure for Static Uplift Resistance of Mortar or Adhesive Set Tile Systems
No. 102-95 - Test Procedure for Static Uplift Resistance of Mechanically Attached‚ Rigid Roof Systems
No. 102(a)-95 - Test Procedure for Static Uplift Resistance of Mechanically Attached‚ Clipped‚ Rigid‚ Roof Systems
No. 103-95 - Test Procedure for Self-Adhered Underlayments for Use In Discontinuous Roof Systems
No. 104-95 - Test Procedure for Nail-on Underlayment for Use In Discontinuous Roof Systems
No. 105-98 - Test Procedure for Field Withdrawal Resistance Testing
No. 106 - Standard Procedure for Field Verification of the Bonding of Mortar or Adhesive Set Tile Systems and Mechanically Attached‚ Rigid‚ Discontinuous Roof Systems
No. 107-95 - Test Procedure for Wind Resistance Testing of Non-Rigid‚ Discontinuous Roof System Assemblies
No. 108-95 - Test Procedure for Wind Tunnel Testing of Air Permeable‚ Rigid‚ Discontinuous Roof Systems
No. 110-2000 - Testing Requirements for Physical Properties of Roof Membranes‚ Insulation‚ Coatings‚ and Other Roofing Components
No. 111(A)-95 - Test Procedure for Roof Edge Termination Performance
No. 111(B)-95 - Test Procedure for Edge Metal Pull-Off Performance
No. 111(C)-95 - Test Procedure for Coping Cap Pull-Off Performance
No. 112-95 - Standard Requirements for Concrete Roof Tiles
No. 112-95 Appendix A - Clarification of Testing Frequency and Sampling Method
No. 114-95 - Test Procedures for Roof System Assemblies In the High-Velocity Hurricane Zone Jurisdiction
114-95 Appendix A - Test Procedure for Above Deck Combustibility ASTM E 108
114-95 Appendix B - Test Procedure for Simulated Dynamic Uplift Pressure Resistance of Mechanically Attached Roof System Assemblies
114-95 Appendix C - Test Procedure for Simulated Uplift Pressure Resistance of Roof System Assemblies
114-95 Appendix D - Test Procedure for Simulated Uplift Pressure Resistance of Adhered Roof System Assemblies
114-95 Appendix E - Test Procedure for Corrosion Resistance of Fasteners‚ Batten Bars and Stress Distribution Plates
114-95 Appendix F - Test Procedure for Susceptibility to Hail Damage for Roof System Assemblies
114-95 Appendix G - Test Procedure for Susceptibility to Leakage for Roof System Assemblies
114-95 Appendix H - Test Procedures for Small Scale QC and Physical Properties of Approved Roof System Assemblies
114-95 Appendix I - Test Procedure for Static and Dynamic Puncture Resistance of Roof System Assemblies
114-95 Appendix J - Test Procedure for 12 Foot by 24 Foot Simulated Uplift Pressure Resistance of Roof System Assemblies
114-95 Appendix K - Test Procedures for F.I.T. Classification of Modified Bitumen Roof System Assemblies
116-95 - Test Procedure for Air Permeability Testing of Rigid‚ Discontinuous Roof Systems
117(A)-95 - Test Procedure for Withdrawal Resistance Testing of Mechanical Fasteners Used In Roof System Assemblies
117(B)-95 - Test Procedure for Dynamic Pull-Through Performance of Roofing Membranes Over Fastener Heads or Fasteners with Metal Bearing Plates
117(C)-95 - Test Procedure for Dynamic Pull-Off Performance of Roofing Fastener Heads or Fasteners with Bearing Plates
121-95 - Standard Requirements for Testing and Approval of Roofing Adhesives‚ Mastics and Coatings
123-95 - Standard Requirements for Mortar Used In Mortar Set Tile Systems
123-95 Appendix A - Standard Requirements of Tile Adhesive Used to Repair or Supplement Tile Attachment
124-95 - Test Procedure for Field Uplift Resistance of Existing Membrane Roof Systems and In Situ Testing for Reroof and New Construction Applications
125-03 - Standard Requirements for Metal Roofing Systems
126-95 - Standard Procedures for Roof Moisture Surveys
131-95 - Standard Requirements for Thermoplastic Olefin Elastomer Based Sheet Used In Single-Ply Roof Membrane
131-95 Appendix A - Test Procedure for Thickness Measurement of Coating Over Class SR Olefin Elastomer Based Sheet Roofing
132-95 - Standard Requirements for Testing and Approval of Sealants Used In Roofing
135-95 - Standard Requirements for Fiberglass Reinforced Tile‚ Shingles or Panels and Fiber Cement Shingles‚ Shakes or Panels
138-95 - Standard Requirements for Aluminum Pigmented Emulsified Asphalt Used as a Protective Coating for Roofing
139-95 - Standard Requirements for White Roof Patch Specification
140-95 - Standard Requirements for Nonfibered Roof and Foundation Coatings
141-95 - Standard Requirements for Coal Tar (Cutback) Roof Coating‚ Brushing Consistency
142-95 - Standard Requirements for Coal Tar Roof Cement‚ Asbestos Free
143-95 - Standard Requirements for White Elastomeric Roof Coatings Used for Coating Built Up Roofs and Metal Roofing Systems
201-94 - Impact Test Procedures
202-94 - Criteria for Testing Impact & Nonimpact Resistant Building Envelope Components Using Uniform Static Air Pressure
203-94 - Criteria for Testing Products Subject to Cyclic Wind Pressure Loading
301-94 - Testing Laboratory
Top
Previous Section
Next Section
Top
Previous Section
Next Section
